Hardwood
Engineered hardwood
Luxury vinyl plank
Laminate
Porcelain tile
Carpet
Shaw
Mohawk
COREtec
PergoFree in-home measure and written estimate: Shaw, Mohawk, COREtec and Pergo lines compared on your own rooms, with carpet, tile, vinyl plank, laminate and hardwood laid out side by side
Get your free estimateTrusted Hardwood Floor Refinishing for North Las Vegas Homeowners
North Las Vegas homes take a beating from the inside out. The same desert sun that bleaches a west-facing wall also fades a wood floor, and the dry air pulls moisture out of boards until gaps open at the seams and the finish starts to crack along the grain. That worn, gray, scuffed look isn’t the end of your floor – it’s usually the topcoat giving up while the wood underneath is still sound. Refinishing sands that tired surface back and builds a fresh finish on top, so you keep the floor you already have instead of paying to tear it out. Our technicians have up to 12 years of experience reading exactly these conditions, and we’ve built a strong local reputation across the valley by telling homeowners honestly whether a floor can be saved or not. Call (888) 515-5223 to set up a free estimate. We answer 24/7 with fast dispatch from 7am to 7pm.
What Our Hardwood Floor Refinishing Service Includes
Refinishing is not one job, it’s a set of decisions made in the right order. Here’s what each piece covers and when it’s the right call for your floor.
Hardwood Floor Sanding
Sanding strips the old finish and a thin layer of the top wood away to expose clean, uniform grain underneath. You need it when the surface is scratched through the finish, when the color has gone patchy, or when a previous coat is flaking and won’t hold a new one. We work through progressively finer grits with dust-controlled equipment, and we check the board thickness as we go, because a floor that’s been sanded heavily before has less room to give.

Hardwood Floor Staining
Staining is where the color of the finished floor is decided, and it happens after sanding and before the topcoat goes on. It’s the step to plan for when the existing color reads too orange, too yellow, or too dark for the room you’re living in now. We test the stain on a spare section or an inconspicuous board first so you can see how it settles into your particular wood, because species take color differently and a sample chip on paper won’t tell you the truth.

Hardwood Floor Restoration
Restoration covers the problems that go beyond surface wear: cupped boards, water-stained patches, dents, and sections that have lifted at the seams. You look at restoration when the floor has a history – a leak, a heavy piece of furniture that sat in one spot, a repair that was never finished properly. We assess what can be sanded out, what can be patched with matching wood, and what honestly can’t be fixed, then give you a written plan before any work starts.

Hardwood Floor Buffing
Buffing is a light mechanical scuff of the existing finish to knock down dullness and minor surface marks, without removing the finish itself. It’s the right step when the wood looks tired but the finish is still intact and the color is still what you want. It’s a smaller job than a full sand, and it buys time on a floor that doesn’t need a full refinish yet.
Screen and Recoat Hardwood Floors
A screen and recoat abrades the topcoat lightly and applies a fresh layer of finish over it, leaving the stain color untouched. This is the maintenance step for a floor whose color you like but whose surface has gone scuffed and flat, especially in doorways and traffic lanes. We test adhesion in a small spot first, because a recoat over a contaminated or failing finish will peel, and we’d rather find that out before we start than after.
Stair Refinishing
Stairs wear faster than any floor in the house because every footfall lands on the same few inches of tread. Refinishing treads, risers and railings brings the staircase back in line with the floors it connects to, and it’s usually done as part of a whole-floor job so the finish matches. We handle the edges, nosings and tight corners by hand where a drum sander can’t reach.
Styles & brands we work with
- Hardwood
- Engineered hardwood
- Luxury vinyl plank
- Laminate
- Porcelain tile
- Carpet
- Shaw
- Mohawk
- COREtec
- Pergo
Brands We Service for Hardwood Floor Refinishing
Refinishing is done on the floor that’s already in your home, so the brand conversation here is a little different than it is for a new installation. Plenty of North Las Vegas homes have engineered wood from Shaw or Mohawk underfoot, and those floors have a wear layer that limits how much sanding they’ll take. We check that before quoting, because sanding through a wear layer ruins a floor that could have been recoated instead. Armstrong engineered products show up often in older valley houses too, and they’re worth a careful look at the edges and seams before anyone touches a sander.
When a refinish is done and you’re thinking about the next room, our product knowledge runs across nine names: Shaw, Mohawk, COREtec, Pergo, LifeProof, Mannington, Armstrong, Daltile and Karndean. For a kitchen or a hallway that sees pets and spills, a water-resistant plank from COREtec or LifeProof is a conversation worth having, and Pergo covers the everyday-durable end of the laminate range. Whether you have a Shaw floor that needs a recoat, a Mohawk engineered plank that needs patching, or any other make, we can help you sort out what’s possible.
Signs You Need Hardwood Floor Refinishing Right Now
- Scratches you can feel with a fingernail. Surface scuffs sit in the topcoat, but a scratch that catches your nail has gone into the wood. Left alone, those scratches take on dirt and moisture and darken into permanent marks.
- Gray or dull patches in traffic lanes. When the finish wears thin in the paths between rooms, the wood underneath starts to oxidize and lose its color. That’s the point where a recoat still works and a full sand is the next step if you wait.
- Gaps opening between boards. North Las Vegas summers pull moisture out of wood, and boards shrink and separate. Small seasonal gaps are normal, but gaps that stay wide after the cooler months point to a moisture problem worth checking before you refinish over it.
- Peeling or flaking finish near sinks and doors. Water and sun both break down topcoats, and once the finish lifts, moisture gets into the wood instead of sitting on top of it. A failing finish is the cheapest problem to fix early.
- Cuping or a springy feel underfoot. Boards that curve at the edges or feel soft when you walk on them suggest moisture from below or a subfloor issue. Refinishing won’t fix that on its own, and we’ll tell you so at the estimate rather than sand over it.
Our Hardwood Floor Refinishing Process – Step by Step
- 1
In-home measure and assessment. We walk the floor with you, check board thickness, test for finish adhesion, look for moisture staining and inspect the subfloor where we can. This is also when we measure the square footage that sets your written estimate.
- 2
Written estimate and plan. You get a written price, a recommended scope (recoat, buff, or full sand and refinish), and the stain and finish direction in writing. No surprises later, and no pressure to add work the floor doesn’t need.
- 3
Preparation and sanding. We protect adjacent surfaces, control dust, and sand through the grits to bare, uniform wood. Edges and corners get hand work where the machine can’t reach, and stairs are handled separately with their own tools.
- 4
Staining and finishing. If you’re changing color, we apply and check the stain before the topcoat goes down. Finish coats are applied according to the product instructions, and the floor gets the cure time the manufacturer specifies, which depends on the product and the humidity in the house.
- 5
Walkthrough and care guidance. We walk the finished floor with you, point out what to expect in the first weeks, and explain how to clean and protect it going forward. The schedule for the work is set at the estimate, and the product instructions set the cure time, not a guess.
See the difference
Before
After
Before
After
Before
AfterHow Much Does Hardwood Floor Refinishing Cost in North Las Vegas?
Hardwood floor refinishing in North Las Vegas typically runs $1675 – $4650, which is the estimated installed price for a 500 to 800 square foot project. Per square foot, refinishing starts from about $3, but the real number depends on the product, the rooms involved and what’s under the floor. A screen and recoat on a floor in decent shape sits at the low end; a full sand, stain and refinish with stair work and patching sits at the high end.
Here’s how the pieces break down:
| Work | Typical estimated range |
|---|---|
| Buff or screen and recoat | Low end of $1675 – $4650 |
| Full sand, stain and refinish | Middle to high end of $1675 – $4650 |
| Restoration with patching or repair | High end of $1675 – $4650 |
| Stair refinishing (when added to a floor job) | Quoted with the project |
What moves the price: square footage, how many rooms and how fussy the edges are, the condition of the existing finish, whether you’re changing stain color, and whether the floor needs restoration work before finishing. You avoid overpaying by getting the scope in writing, asking whether a recoat is genuinely an option, and not paying for a full sand on a floor that only needs a buff. Every free estimate includes the measure, the condition assessment, and a written price, and that written estimate sets the final cost.
Hardwood Floor Refinishing Near North Las Vegas – Our Service Area
We work across North Las Vegas and the surrounding communities, including Sunrise Manor, Winchester, Whitney, Paradise, Spring Valley, Summerlin, Henderson, Enterprise, Boulder City, Las Vegas and Moapa Town. Each of these areas has its own housing mix, from older valley homes with original oak to newer builds with engineered planks, and the assessment visit tells us which one you’re dealing with. The best way to know what your floor needs is a free in-home estimate. See our full flooring installation North Las Vegas services if you’re weighing refinishing against a new floor.
Serving North Las Vegas, NV – Our Local Coverage Area
We serve North Las Vegas and nearby communities. Use the map below to see the area we cover. If you’re nearby, we can almost certainly help.
Frequently Asked Questions – Hardwood Floor Refinishing in North Las Vegas
Hardwood floor refinishing is the process of sanding off the old finish and stain and applying new ones to the wood you already have. It restores the surface without replacing the floor, and it’s the right move when the wood is structurally sound but the topcoat has worn out. It’s different from a recoat, which only adds a fresh top layer without sanding down to bare wood.
There’s no fixed number of days, because the schedule depends on the square footage, the condition of the floor, the number of finish coats, and the cure time the product requires. A recoat is a shorter job than a full sand and refinish, and stairs add their own time. We set your schedule at the estimate so you know what to plan for, and we tell you in writing before work begins.
Typical estimated pricing in North Las Vegas is $1675 – $4650 for a 500 to 800 square foot project, with refinishing starting from about $3 per square foot. Stair work, restoration patching and color changes can push the price toward the higher end, while a simple recoat sits at the low end. Call (888) 515-5223 for an exact quote – estimates are free.
We assess engineered floors from Shaw, Mohawk, Armstrong and others on a case-by-case basis, because the wear layer on top of the core limits how much sanding the floor can take. Sometimes a recoat or buff is the right answer instead of a full sand, and we’ll tell you which at the estimate. We don’t promise that every engineered floor can be refinished; the condition check decides that.
We answer 24/7, and fast dispatch runs from 7am to 7pm, Sunday through Friday, and we’re closed Saturday. Refinishing is a scheduled job with a free measure and estimate first, then a written price, then a booked work day, so the schedule is set at the estimate. A call outside dispatch hours is booked into the next opening, Sunday through Friday, 7am to 7pm.
Our installation workmanship is backed, and the finish products we use carry their own manufacturer warranties. The specific terms depend on the product chosen, so we spell them out in your written estimate rather than quoting a term here that may not apply to your floor. Ask at the estimate and we’ll walk through exactly what’s covered.
Clear the rooms of furniture, rugs and anything on the walls that could collect dust, and expect to stay off the finished floor for the cure period the product requires. If you have pets, plan to keep them off the work area. The written estimate and the product instructions set the specifics, and we’ll confirm the prep list with you before the work day.
Schedule Your Hardwood Floor Refinishing Service in North Las Vegas Today
Your floor may have years left in it. A free in-home estimate tells you whether a buff, a recoat or a full refinish is the right call, and you get a written price before anything starts. Call (888) 515-5223 to schedule your no-obligation estimate. We answer 24/7, and our technicians have up to 12 years of experience across North Las Vegas and the neighborhoods around it. You can also read more about North Las Vegas and our Winchester service area, or look at carpet installation if another room is next on your list.
Written by the team at Flooring Installation North Las Vegas.